info@xmperfectstone.com +86-592-2916208
How To Cut Marble Slab By Hand

How To Cut Marble Slab By Hand

Aug 21, 2020

Since marbles are available in different sizes, you can use different types of marble, such as marble with different shapes and sizes and even different types of stones. 


You need to know the size and thickness of the marble you want to cut, and if your marble is more than 16 inches tall, you can use a wet saw blade tabletop, but it simply won't be cut at all. If you are cutting a thin marble slab for your countertop, you must use a diamond blade supplied with a circular saw. 

The blade, designed for cutting tiles of all kinds, will hardly leave a dent in the granite, and granite is harder than ceramics or marble. 


Carefully measure how much you need to cut each tile, and then create cuts with an indelible marker. Any faulty ink that remains on the tile after the cut can be removed with a little rubbing alcohol and a cloth. 


First, the area where the cuts are to be made is covered with tape. Then, the circular saw is pressed down the length of the marble with a clamp and a straight edge so that straight lines can be cut and a clear line can be maintained between the cut edges and the marble product itself. Another way to prevent chipping at the edge during the cutting process is to cut material from the back of a marble product so that the chips do not see through the installed marble product. 


As soon as the chips are formed, they can be smoothed with sandpaper or a belt sander or even with a belt sander. Remember that you can scratch the surface of the marble, so limit polishing to the edges where the cuts are made. 


Most residential and utility tile saws you rent in your hardware store only cut 24-inch tiles, which means that the panel size is limited to 24 inches in width. If you have a friend who owns one, the principle is the same: place the plates in a tray and guide the blade through the stone. If your slab is big enough to fit into the wet saw, you can also use a tile saw to cut marble. Commercial saws are sometimes available for rent or purchase, but they are not ideal for this type of work. 


For this reason, this work requires a wet saw with a diamond blade, and it should not be tried with just a saw. If you are massively rebuilding your house, you will be better off buying only the saw, because you will only do one job and need it for several jobs. However, if you only do one or two jobs at a time, you may be well advised to rent the sea. Saw for a few months or even a year. 


This is used to reduce the heat and pressure caused by marble cutting and is used to cut a variety of materials, including wood, stone, wood chips, glass, metal, plastic, and other materials. 

The segmented, continuous edge of a diamond blade uses powder metal to hold the diamond in place, and it cuts through the stone with ease. 


The thickness of the bond determines the speed at which the diamond is exposed during the use of the blade. Diamond concentration is higher when the bond holding strength is strong, and the higher the strength, the greater the concentration of the diamonds. Bond strength is soft, medium, or hard, with diamonds with a softer bond being exposed more quickly. 


Saws with a lot of horsepowers often need a strong blade with a high diamond concentration for the durability and longevity of the blade, and saws with a lot of horsepowers need strong blades with higher diamond concentrations. 


High diamond concentrations and coarse grains are ideal for cutting abrasives, especially when cutting hard, dense materials. Segmented blades have a medium-hard bond, and blades with low diamond concentration or coarse gray tones are popular for more efficient cuts where smooth cuts are irrelevant. 


Although knives can provide relatively smooth cuts at high cutting speeds, fragmentation can occur during the cutting process. It is not necessary to cut with a high diamond concentration or coarse grey tones, as is the case with high diamond grinding blades. 


A is available in a wide range of diameters, from small to large, but the 12 'diameter and the larger market are particularly dominated by high diamond grinding wheels with a diamond concentration of 1.5 - 2.0%. 

The type of tool used to cut the marble is dictated by the place where you install it. Once you are ready to use the tool, you will need a diamond carbide blade to cut the marble properly. 


You can simply have a diamond cutter for egg cutting plates or cut the block as soon as it arrives at your stone cutting and manufacturing plant. After cutting it from 2 cm to 3 cm (3.5 cm), you run it through a huge saw to make many stone discs at once.